Reasons to turn off your gas fireplace pilot light: Click here for instructions on how to reprogram your remote.
Slide the switch on the receiver back to the center or remote position.
How to turn off gas fireplace without remote. If you have tried to light the fireplace but nothing is happening, first check that the gas valve is in the on position and emitting gas. They may be located behind a metal grate or plate. If so, you will have to access the control box, which is located either beneath a fireplace model, or behind a stove model.
She had to press the on/off button several times before it turned off. Put the pilot light starter in the ignite position and press down on the knob firmly. You will need to remove the decorative logs and place them on the tarp.
Follow the steps below to light your gas fireplace by turning the gas on inside. Before troubleshooting your remote, however, make sure you can still ignite your fireplace at the unit itself. The next step and how to light a gas fireplace is to find the ignition button.
You should begin to hear a clicking sound. If you have a wireless remote control, or a wall switch with a display, find the control box of the fireplace and switch to manual. By selecting ‘on’ your hearth product should function normally without the.
Using the receiver box of your fireplace remote control system, move the switch to the “on” position. The fireplace continued to run. Once the pilot is lit, you can leave the fireplace pilot on and turn the fireplace on and off at the switch, remote or other application.
If your fireplace turns on this way, your handheld remote may need batteries or may need to be reprogrammed. Although the flame from a pilot light is small, it’s still heat. When she pressed the on/off button, nothing happened!
First, you will need to turn the gas valve on the front of the unit to the off position. If the fireplace hasn't lit up within 10 seconds, wait at least 10 seconds before trying again. You will often find the fireplace controls on the floor of the fireplace.
If the fireplace has a control panel that you can access, turn the knob to “off.” make sure that the emergency gas valve is turned to the closed position as well. There are many reasons a remote control could stop functioning correctly. Next, put a tarp down, in front of the fireplace.
Once all switches have been reset to the correct position, the remote control unit should be back in control of your fireplace and the transmitter & receiver should communicate electronically again. If you smell gas near your furnace, look for a valve handle on the gas pipe close to the body of the furnace. Once you have located the controls, there will be a visible switch that has the options ‘off’, ‘on’, and ‘remote’.
Most models have a switch that slides between ‘manual’ and ‘remote’. If you’re working with a fireplace key, place the key into the slot. But, because fireplaces go long periods of time without use, getting the remote synced back up with the fireplace can take some.
You can even use your gas to help the fire get started for a few minutes, then turn it off. Turning it so the handle is positioned at 90 degrees to the line of the pipe will turn off the gas. The fireplace came with a firegenie remote.
If your fireplace includes a gas shutoff valve, make sure. Depending on where you live, you might not want any extra heat being generated inside your home during the blazing summer months. Once you have determined that the remote receiver is in working condition, turn it to the manual mode, and try to turn on the fireplace using the manual on/off switch.
If it was previously on, turn the knob to the off position and wait at least five minutes to allow any lingering gas to disperse. “aux on/off” button once will start the heater and it will run at a medium heat (high for df) output setting until the “aux on/off” is pushed again to shut the heater down. Ultimately it is best to consult your appliance manufacturer instructions or the installation technician, so that they can guide you on how to operate your gas fireplace without electricity.
It may take a few tries to get the fireplace to ignite. A slide switch on the receiver has been moved to the on position. Browse heat & glo's remote control faqs section for answers to questions about our remote control products.
If the gas shutoff valve is not immediately visible, trace the gas pipe backward from the furnace. This past week, there were a couple of times when, after running the fireplace throughout the day, my mother wanted to turn the fireplace off. Now you will need to loosen the screw that holds.
The auxillary on/off button is used to turn the fireplace on without the remote control, and also used for “teaching” the fireplace to. One reason for turning off the pilot light is heat. Simply lower or raise the cover over the controls for access.
See your owner’s manual for specifics about lighting your gas fireplace without a remote control. Once you have done this, allow some time for the unit to cool down. Without a remote there will typically be an ignition button on the control panel of the fireplace.
Gas fireplaces are safe to burn wood in like a standard fireplace, so a duraflame log is perfectly fine to burn in your gas fireplace. Fireplace remote control troubleshooting + faqs | heat & glo au25qienmv1b5d5yu2yuutjg