How To Hang A Turkey Fan On The Wall

If space and/or finances are at a minimum, a sensational trophy display can be created using the barn wood turkey tail panel to feature the fanned tail and beard of your wild turkey. Removing the fan is one of the first things that i do after gutting the turkey in order to avoid unnecessary damage during the transport and cleaning process.

Turkey fan and beard mount display taxidermy walnut plaque

The overall length of the plaque is 14.5.

How to hang a turkey fan on the wall. Cut about 4 or 5 inches of string and use a couple of small pieces of tape to. This would also be a good choice if the body or wings were damaged beyond repair. Instructions for assembly are provided at this link.

What he wants is the full cape or back feathers and the tail and wings to hang on the wall. Install the hanger bracket on back of the panel. This would also be a good choice if the body or wings were damaged beyond repair.

This is a turkey fan and beard display made from reclaimed barn wood. When done, place another piece of cardboard over the fan, and. Ensure to use a strong tape such as masking tape or a thin piece of duct tape and any type of thin cord or string.

Fan and beard mounts with a plaque is $125.00. The edges have not been routed for more of a rustic look to the plaque. Drive a 6 or 8 d nail through the cape until the nail comes out the skin side.

The edges have not been routed for more of a rustic look to the plaque. This plaque comes ready to hang on the wall. Align the fan so it sits centered and level near the bottom of the frame.

This will hold everything in place. If space and/or finances are at a minimum, use the barnwood turkey tail panel to display the fanned tail and beard of your wild turkey. This article will walk you through step by step, from shot to wall, how to make a fan mount of your own.

Follow these steps for the best way to dry a turkey fan… remove tail fan from your bird. This plaque comes ready to hang on the wall. When the bondo is dry, place the tail in the center of the panel and attach the beard to the rosette with tack or hot glue.

This is a turkey fan and beard display made from reclaimed barn wood. The feature that makes walnut hollow's products stand above the rest in the market is the wide variety and high quality images on the plaques. Make sure to correct any small misalignments now, because once the turkey fan dries, you won’t be able to fix it easily.

This allows the plaque to lay flat against the wall. The overall length of the plaque is 14 3/4. Watch how it works in this video….

I used hot glue and screws with cardboard on the back to keep the wings mostly flat and secured to the lower panel. The only things left to do are find a wall, pound in a nail and hang it up! There is a slot cut for the beard and the plaque has a keyhole cut in the back for flush mounting to the wall.

There is a slot cut for the beard, and two slots cut to mount the turkey legs to display the spurs. ** the plaque shown is the plaque you will receive. Easy made turkey fan slots requires no drilling and there is also a cutout slot for your tom's beard to hang from.

So has the desire to create beautiful turkey fan mounts and turkey beard mount displays & plaques. Place the rosette over the tail base and install the screw. This is how you will hang your fan on the wall.

Work borax into remaining skin or meat for drying. I'm looking for any tips on how to precisely and symmetrically attach turkey wings to a panel. Set the fan in position and let set, then do the other side.

This plaque comes ready to hang on the wall. I do charge $375 for standing or flying bird and $450.00 for a full strut bird. Hold the cape on the wall and tap the nail until it’s mounted on the wall.

Attach to hanger clips as seen in video below. I sandwiched the fan base between two pieces of wood with hot glue and one screw that would allow for fine tune rotation. Insert the base of your turkey beard into the open end of the spent hull and secure it in place with a drop or two of hot glue.

There is a slot cut for the beard, and two slots cut to mount the turkey legs to display the spurs. I have a 1/4″ blade for my bandsaw for cutting curves like this, but currently i. The overall length of the plaque is 19 and the width is 7.75.

I have seen this type of mount done with a felt border but this is not what he wants. With the glue dried, i traced the patterns onto the wood heavily with a ballpoint pen, then removed the patterns and traced over the dents left behind in the wood. There is a slot cut for the beard and the plaque has a keyhole cut in the back for flush mounting to the wall.

The edges have not been routed for more of a rustic look to the plaque. The overall length of the plaque is 17. Trim meat and fat from the tail fan butt.

Lay feathers up, grasp the fan and determine approximate center of fan where quills meet. Now you are ready to show off your beautiful tail mount! Lay the tail on cardboard or old newspapers and peel back the skin from the flesh toward the feathers on both sides to expose the knob of flesh and bone that holds all of the tail feather quills.

Don’t pin the quills themselves, but place the pin in front of the feathers to stop them from pulling back into a closed position. To mount the cape is easy. This plaque comes ready to hang on the wall.

Adjust the string length so the top of the shotgun shell will hang directly below the middle of the fan where all the feathers meet the flesh. Simply use a nail or screw to hang the plaque using the keyhole slot. Not to mention, the wood is of the highest quality and is easy on the eyes.

Lay the fan onto a piece of cardboard, and use small pins to hold the feathers in place. Add your dried tail fan to the display by dropping it. Mexican wedding decorations candy table decorations fall table centerpieces rustic headboard diy rustic sofa turkey mounts turkey fan blue grey walls turkey images

Avoid studs as just the drywall penetration will hold. The plaque has a keyhole cut in the back for flush mounting to the wall. Remove the fan and beard.

The plaque has a keyhole cut in the back for flush mounting to the wall. Place the fan in a refrigerator for a few days or freezer until you are ready to proceed.

How To Mount A Turkey Fan Turkey fan, Hunting decor