How To Install A Freestanding Tub Filler On Concrete Slab

Insert tubing riser into tub filler main body and secure with set screw located at the base of the main body. Ensure the tub filler handle is in off position, turn on water supply to test water connections to confirm water tight seals.

The Hibiscus Freestanding Tub Faucet combines contemporary

This traditional faucet will arrive completely assembled.

How to install a freestanding tub filler on concrete slab. Carefully inspect the tub for any damage (i.e., chips, scratches, cracks). • move the bathtub down slowly by removing the pieces of lumber. Doing this avoids the awkward procedure of shimming up the tub after placing it unless your tub sits on adjustable feet.

Take a look at this guide to freestanding tub fillers and scroll down until you see the video. It also comes with all necessary accessories for easy installation and uses. Please use teflon tape on all threaded connections to ensure a sealed connection.

Includes mounting bracket, manifold, and mounting screws. This allows you to see the leveling feet (if any) and the connection points for the plumbing. 3 4×4 4×4 3 3 1 2 floor level floor level

Also, check for the screws to ensure that they are tightened accurately. If i dont reinforce with concrete back fill the tile around the tub filler flange is not supported. Once you have the tub in place the plumber with mark where the drains need to go he will then bust through the concrete slab go down as far as he can to where he can maneuver the plumbing, reroute the plumbing to wear the new drain is going to be just like the one you have for the existing how it’s plumbed up for the old tub he does the same thing with the new.

• fill the water in the tub and let it drain out. Traditional tub filler installation guide note: The water inlets have a 7” on center spread.

Hj (az) unfortunately, with that faucet it appears the connections have to be below the floor which would make them difficult to connect with a concrete floor, when you cannot make the connections above. The video shows installation on a wood floor but below that you will find links to the actual installation instructions which have information on how to modify the installation for concrete floors. Concrete mounting kit for installation of moen single riser freestanding tub filler.

Allows for construction or a renovation project to proceed without delays when narrowing down a design style. Freestanding installation drain body washer warning: Due to the rough handling during shipping or on the job site, do not install this product until a thorough inspection and water test has been completed.

Installing freestanding tub faucet on concrete slab; Then bolt a steel plate higher up to floor surface to support the tile. Connecting tub filler inlets to water supply:figure 4 illustrates the connecting of the tub filler

Trim kit is sold separately and is required to complete the unit. The tub filler has large parts so that water can flow at a higher rate. I have copied this information from the valve installation instructions which is the section that explains how to install the freestanding faucet on a concrete floor:

Delta makes two styles of freestanding bathtub filler valve: If the bubble doesn't center, spread concrete floor leveling compound over the entire part of the floor that's under the tub and screed it level with a straight piece of wood or metal. Adjust according to the height of the faucet base and make sure that the mounting flange (escutcheon mounting plate) is level with the finished surface of the floor.

• fill the spaces with silicone. Save time, effort, and money on future renovation. Woodbridgee f0006blrd contemporary single handle floor mount freestanding tub filler faucet with hand shower in matte black finish.

As you are about to finish your bathtub installing on the concrete floor, fill up the tub and make sure, the overflow drain and stopper are working properly. Once you have the tub in place the plumber with mark where the drains need to go he will then bust through the concrete slab go down as far as he can to where he can maneuver the plumbing, reroute the plumbing to wear the new drain is going to be just like the one you have for the existing how it’s plumbed up for the old tub he does the same thing with the new. To get your freestanding tub ready for complete installation, set two 4x4s in place in the desired tub location to hold up the bathtub;

The wood support should be at least 2 thick. Sturdy mounting bracket included with valve eliminates wobble. A couple of ideas are:

• pour concrete filler (15) around mudguard encasing plate and filling to surrounding concrete⓮ • apply top floor covering⓭ (e.g. Also, learn how to swap the cartridge out and the diverter. Backfill a recessed pocket to bolt the rough in to.

Make sure this fits by entering your model number. Secure the spout into position by tightening the set screw located at the top of the tub filler main body. Check bathtub for correct model and size.

Quality construction with elegant design contemporary freestanding floor mount tub filler faucet with telephone style hand shower, fine autistics craftmanship, made from solid brass construction for reliability and. • from the bottom, make sure that all the joints are watertight. Tile, stone, etc…) onto concrete filler (15) and.

Sebastian Freestanding Tub Faucet, Supplies, Valves